Brushbond FLXIII

Features & Benefits

• Can be applied to damp substrates
• No primer required
• Elastomeric - able to bridge cracks
• Able to take foot traffic when cured
• Factory pre-blended two component system ensure
• quality control at site

Technical Specifications

Specifications coming soon. Contact us for full technical details.

Applications

The Brushbond FLXIII Liquid concentrate is poured from the plastic container into the metal drum supplied and mixed mechanically with a slow speed drill (350-450 rpm) fitted with a Fosroc Mixing Paddle (MR3). Add the powder component gradually to the liquid avoiding lump formation and mix for 4-5 minutes until a smooth consistent mix is achieved. Use the material within the recommended pot life. UAE/0288/11/J Fosroc Brushbond FLXIII Al Gurg Fosroc LLC Post Box 657, Dubai United Arab Emirates www.fosroc.com

• For best results damp the surface before coating with
• Brushbond FLXIII. Use a short, stiff bristle brush preferably
• to 200 mm in width. Apply like a paint using one or two
• coats as required.
• For trowel application, ensure that the substrate is levelled
• and repaired of any undulations or pot holes.
• Brushbond FLXIII should be applied to the recommended
• coverage as follows:
• It is recommended that general re-surfacing and areas
• subjected to light foot traffic should receive a Brushbond
• FLXIII in two coats of 500 microns each to give a 1mm thick
• coating. Additional coatings may be required for areas of
• moderate to heavy pedestrian conditions.
• Cleaning
• Brushbond FLXIII should be removed from tools and equip-
• ment immediately after use with clean water. Hardened
• material can only be removed mechanically.
• Technical Service
• Fosroc offers a comprehensive technical support service to
• specifiers, end users and contractors. It is also able to offer
• on-site technical assistance, an AutoCAD facility and dedi-
• cated specification assistance in locations all over the world.
• Limitation
• Brushbond FLXIII should not be applied if the air or
• substrate temperature is greater than 45°C. This may
• result in different colour shades.
• Estimating
• Supply
• Brushbond FLXIII Kit : 15 litres pack
• Powder : 14.8 kg
• Liquid : 10 kg
• Coverage / yield
• Brushbond FLXIII : 15m²/pack applied at 1mm
• thick (2 coats of 500 microns
• thick)
• Note: Coverage figures are theoretical and due to
• wastage factors and the variety nature of possible
• substrates, practical coverage will be reduced.

Frequently Asked Questions

• Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
• Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.
• Head Office
• telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
• Regional offices
• Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
• Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
• Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
• Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
• Denotes the trademark of Fosroc International Limited
• †
• See separate data sheet

Brushbond FLXIII has a shelf life of 6 months in unopened pack, kept in a dry store, between 35 0 C and 10 0 C In high humidity locations, the shelf life may be reduced to 4 months. The liquid and powder components must not be allowed to freeze.

Gloves and goggles should be worn. Any splashes to the skin or eyes should be washed off with clean water. In the event of prolonged irritation, seek medical advice. Powder products should be handled to minimise dust formation; use a light mask if excessive dust unavoidable.

For porous substrate (Gypsum board) application, Nitobond PVA should be applied to seal the surface. followed by the application of Brushbond FLXIII.

Customer Reviews

No reviews yet. Be the first to review this product.

Delivery & Returns — UAE