Trafficguard Top Coat

Tools and equipment should be cleaned immediately after use with Fosroc Solvent 102. Epoxy Polyurethane based Hard wearing, skid resistant, flexible Top Coat for Traffiguard System UAE/0677/16/E Fosroc Trafficguard Top Coat Al Gurg Fosroc LLC Post Box 657, Dubai United Arab Emirates www.fosroc.com

• Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
• Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.
• Head Office
• telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
• Regional offices
• Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
• Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
• Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
• Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
• Denotes the trademark of Fosroc International Limited
• †
• See separate data sheet

Fosroc offers a comprehensive range of high performance, high quality repair, maintenance and construction products. In addition, Fosroc offers a technical support package to specifiers, end-users and contractors, as well as on-site technical assistance in locations all over the world. Estimating

Trafficguard Top Coat has a shelf life of 6 months if kept in original unopened containers at temperatures between 5 0 C and 30 0 C in a dry environment.

Trafficguard Top Coat should not come into contact with skin and eyes or to be swallowed. Some people are sensitive to resins and solvents so gloves and a barrier cream such as Kerodex Antisolvent, Rozalex Antipaint, Debba-Wet Work or similar should be used when handling these products. Remove contamination from the skin with soap and water or a resin removing cream such as Kerocleanse Standard Grade Skin Cleanser or Rozaklens Industrial Skin Cleanser. Follow by washing with soap and water. Do not use solvent. The use of goggles is recommended but should accidental eye contamination occur, wash thoroughly with plenty of water and seek medical treatment immediately. If swallowed, seek medical attention immediately - Do not induce vomiting. Fire Trafficguard Top Coat and Fosroc Solvent 102 are flamma- ble. Do not use near a naked flame. Flash points Trafficguard Top Coat : 23ºC

It is suggested that the following list of equipment is adopted as a minimum requirement. Protective clothing : Protective overalls : Good quality gloves, goggles and face mask Preparation equipment : Stiff wire brush : Proprietary blasting equipment Mixing equipment : 1KW slow speed heavy duty drill, 400 - 500 rpm : Fosroc MR2 mixing paddle Application equipment : Brush or Roller Page 2 of 3 constructive solutions Application - points of note Fosroc operates a policy to encourage the use, where possible, of approved or licensed applicators. This ensures that repairs are completed satisfactorily so that the long-term performance of the materials is assured. For contractors who wish to apply the materials themselves Fosroc is also able to offer technical assistance and training, either on-site or at its Training Centre in Dubai Section B : Application Method 1.0 Surface Preparation 1.1 Concrete Surfaces 1.1.1 Clean the substrate free of all dust, loose material, laitance, oil etc. by light grit blasting or water jetting. 1.1.2 Prior to commencing application dry out any standing water using a sponge. 1.1.3 The substrate irregularities should be repaired using the appropriate Fosroc Nitomortar product. 2.0 Priming 2.1 Always use Trafficguard Primer for priming the substrate, be it metal or concrete. 2.2 Trafficguard Primer should be mixed in the same fashion as that of mixing Trafficguard Top Coat. 2.3 Whilst Trafficguard Primer is still wet, seed with Fosroc Antislip Grain No. 2 at an estimated rate of between 0.4 – 0.8kg/m² 3.0 Mixing 3.1 Stir the contents of the resin base tin to disperse any settlements. 3.2 Pour the entire contents of the hardener into the base container and mix the two materials thoroughly until a uniform colour and consistency is achieved. 3.3 Use a Fosroc mixing paddle MR2 attached to a slow speed drill to mix the components together. 4.0 Application Page 3 of 3 constructive solutions Trafficguard Top Coat, should be applied only in well-ventilated conditions, except otherwise when respirators are used mandatorily. 4.1 Apply Trafficguard Topcoat to the primed surface at an application rate of 0.2 to 0.5 ltr/m² per coat. Trafficguard Top coat is designed for application in one coat on primed surface. 5.0 Cleaning 5.1 Clean tools and equipments with Fosroc Solvent 102 immediately after use. Section C : Approval and variations This method statement is offered by Fosroc as a ‘standard proposal’ for the application of Trafficguard Top Coat. It remains the responsibility of the Engineer to determine the correct method for any given application. Where alternative methods are to be used, these must be submitted to Fosroc for approval, in writing, prior to commencement of any work. Fosroc will not accept responsibility or liability for variations to the above method statement under any other condition.